Click for Abeking Click for Westport Click for Northern Lights Click for Abeking Click for Cross

alarm on DD 8v92

Discussion in 'Engines' started by praetorian47, Sep 18, 2017.

You need to be registered and signed in to view this content.
Page 1 of 3
  1. praetorian47, Sep 18, 2017
    #1
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    I've been getting an intermittent alarm on my starboard engine when running, and now it's pretty constant.

    I believe it's an oil pressure alarm, but the gauge shows it's perfect. Could it be a bad alarm? Sensor?
    Any ideas on where to start will be appreciated!
  2. Capt Ralph, Sep 18, 2017
    #2
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,427
    Location:
    Satsuma, FL
    I'm guessing it's a catch-all bell going off that is your alarm. Are you noticing an oil light blinking?
    Boat brand?
    When you shift at idle, At idle, at low or higher rpm?
    Cold, Hot? Using what weight oil? CF2 oil?
    Were going to need some of these extra details to help.

    For example, my Bertram uses fuel pressure to arm low or high speed oil pressure alarms.
    Old Hat's did this on another path.
    Old Hat's used the same alarm for clutch pressure, so when fast shifting, you never knew if it was a clutch or main oil alarm chirping.

    The more details you can offer, the better we can help without a lot of guessing.

    ,rc
  3. praetorian47, Sep 18, 2017
    #3
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    It's an 88 Ocean 55SS.
    It started happening at idle, in gear, but now is going pretty much all the time after the engine is warm.

    I'm a bit new to it, so ask anything - I'll answer everything I can but I just don't know everything I should add.

    Thanks!
  4. Capt Ralph, Sep 18, 2017
    #4
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,427
    Location:
    Satsuma, FL
    Just at idle?
    What oil specs?
    Hours on engine and oil. RPM at idle in gear?
    Clears with a little throttle?
  5. praetorian47, Sep 18, 2017
    #5
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    Originally it cleared with a little throttle. It happened when I put it in gear and the RPM dropped a bit. It's now happening at just about any RPM.
    It's my first year on the boat, but the PO says he used straight 40 weight, DD oil.
  6. Capt Ralph, Sep 18, 2017
    #6
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,427
    Location:
    Satsuma, FL
    It it low or you added oil?
    Level should be checked many hours after shut down. Level rite at the full line.
    API CF-2 ONLY oil @ 40 wt.
    Or, have you noticed the oil level coming up?

    So, far, you may just have a oil alarm switch messing up but it's a boat engine. Lets keep going and make sure.
  7. praetorian47, Sep 18, 2017
    #7
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    I check the oil before every run and top up as needed. I didn't check before yesterday's ride back to the dock though, so that could be an issue.

    The engines do burn a bit of oil after long runs, so I was advised by the PO to check before every trip.
  8. Capt J, Sep 18, 2017
    #8
    Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,524
    Location:
    Fort Lauderdale
    Start ohming out all of the alarm senders and inspect the connections at the same time. You should have about 4 per engine: oil pressure, coolant temp, gear pressure, gear temp.
  9. Capt Ralph, Sep 18, 2017
    #9
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,427
    Location:
    Satsuma, FL
    After these long runs, when do you check the oil, Many hours later / next morning OR a few minutes after shutting down?
  10. praetorian47, Sep 18, 2017
    #10
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    Days later, just before firing up and going out again. Engines cold.
  11. Capt Ralph, Sep 18, 2017
    #11
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,427
    Location:
    Satsuma, FL
    Back to the top, are you noticing an oil light or just a catch all alarm light?
  12. Capt Ralph, Sep 18, 2017
    #12
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,427
    Location:
    Satsuma, FL
    Great. What oil are you using?
  13. praetorian47, Sep 18, 2017
    #13
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    Its an alarm buzzer. All gauges read perfect, and identical to the other engine.
  14. praetorian47, Sep 18, 2017
    #14
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    Detroit 40 wt.
  15. Capt Ralph, Sep 18, 2017
    #15
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,427
    Location:
    Satsuma, FL
    Same buzzer for both engines? any way to define what engine is alarming?
  16. praetorian47, Sep 18, 2017
    #16
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    capt j, is it possible or likely that I have a different sensor for the alarm and gauge? Maybe the alarm sensor is bad?
  17. praetorian47, Sep 18, 2017
    #17
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    Different buzzer per engine - it's the stbd engine.
  18. Pascal, Sep 18, 2017
    #18
    Pascal

    Pascal Senior Member

    Joined:
    Feb 29, 2008
    Messages:
    8,543
    Location:
    Miami, FL
    If your oil pressure gauge shows correct pressure, it sounds like the alarm sender is bad. replace the sender or as a test swap with the other engine. Or test it with a meter
  19. praetorian47, Sep 18, 2017
    #19
    praetorian47

    praetorian47 Senior Member

    Joined:
    Aug 22, 2011
    Messages:
    258
    Location:
    Bayport, Midland, Ontario
    I'd like to test with a meter - what would I be looking for on a bad one vs good?
  20. Capt Ralph, Sep 18, 2017
    #20
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,427
    Location:
    Satsuma, FL
    At least two senders for the oil pressure system. One to the gauge(s) and one (or more) to the alarms.
    Just remove the wire from the smaller (NC, normally closed) sender. If you find two small pressure switches, try one at a time.

    Foaming oil (wrong or overfill oil) will cause these alarms.

    Dual oil pressure switches armed by fuel pressure; the fuel pressure switch may be arming to early.
Page 1 of 3