Click for JetForums Click for Perko Click for Delta Click for Westport Click for Mulder

135 OptiMax data requested

Discussion in 'Engines' started by Capt Ralph, Nov 7, 2024.

You need to be registered and signed in to view this content.
  1. Capt Ralph, Nov 7, 2024
    #1
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,436
    Location:
    Satsuma, FL
    I did not use the SmartCrap (CANbus) data lead and gauges on my 2003, 2.5L, 135HP OptiMax install. Still available but replacing/repairing the CANbus gauges was just going to cost way to much. Maybe later.
    So I'm pushing a digital engine with an analog dash.
    Pulled out some old FloScan equipment from the depths of my old shop and have it installed also.
    Tach, GPH, MPG, total use and more are available.
    Just need to dial it all in.

    So, I'm looking for the fuel consumption/load data on this 20 year old outboard.
    Anybody have anything in their archives?
  2. Capt J, Nov 11, 2024 at 12:19 PM
    #2
    Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,530
    Location:
    Fort Lauderdale
    No but a Mercury analog smartcraft tach with the little LCD screen at the bottom will give you GPH and the information you're seeking.
  3. Capt Ralph, Nov 11, 2024 at 1:58 PM
    #3
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,436
    Location:
    Satsuma, FL
    Hummmm,,, Must be my poor typing skills.
    I did not install the SmartCrap stuff.
  4. Capt J, Nov 12, 2024 at 12:18 AM
    #4
    Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,530
    Location:
    Fort Lauderdale
    The 4" round gauge should plug right into the harness.
  5. Capt Ralph, Nov 12, 2024 at 8:46 AM
    #5
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,436
    Location:
    Satsuma, FL
    I found it, It is my poor communication and typing skills. Sorry all, I'll try better next thread.
    I did not expand enough that the gauges were not working and not installed.
    Should of included a picture of them with missing lens and sun-burnt LCD screen on the bottom and not working, requiring replacing/repairing them.
    20241022_092840a.jpg
  6. Capt J, Nov 12, 2024 at 3:55 PM
    #6
    Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,530
    Location:
    Fort Lauderdale
    Gaugesavers will fix them for around $100. But they will show you GPH, record fuel used, as well as a lot of other parameters. They'll show you mpg IF you have the transducer installed or hooked to a gps......you can find them used pretty reasonably.
  7. Capt Ralph, Nov 12, 2024 at 4:32 PM
    #7
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,436
    Location:
    Satsuma, FL
    Gaugesavers is rite up the road. Around $150 to 175 each.
    Found a kid down your way that will fix both for $200.
    Still my poor communication skills. Should of included copies of the estimates.
    Unless, somebody else wants to pay for them??
    Humm, maybe should of started a Go-Fund-Me site.
    Oh wait, I already did for our Bertram years ago. Big zip collected.

    Skippy J, I know all this stuff.
    I don't have the funds to make it fancy rite now.
    I have piles of Flowscan stuff in my shop collecting dust that is free. Just need to fine tune them.
    Hence post #1 that I keep quoting.
  8. d_meister, Nov 13, 2024 at 12:18 PM
    #8
    d_meister

    d_meister Senior Member

    Joined:
    Mar 4, 2010
    Messages:
    481
    Location:
    La Conner, WA.
    Too bad you don't have at least one working unit so you can temporarily plug it in to get the data you need. Are there adapters that can allow an OBDII reader to get info? I've often thought about this when having the Cat guys connecting their laptops to the engines on the boats I ran.
  9. Capt Ralph, Nov 13, 2024 at 1:36 PM
    #9
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,436
    Location:
    Satsuma, FL
    Replacing the gauges would be cheaper than the Merc SmartCrap adaptor.

    I'm not only in the dawg house, I'm in the dawg house basement.
    Da wife is still pissed at me. Been a year and she has not been able to use the boat yet and the checking account is thin.
    !cid_01b301d651b0$5a3dc5a0$1401a8c0@RC77.gif


    If I could only sell the fine 125HP that came off.
    Ads coming soon to YF.
  10. d_meister, Nov 13, 2024 at 2:18 PM
    #10
    d_meister

    d_meister Senior Member

    Joined:
    Mar 4, 2010
    Messages:
    481
    Location:
    La Conner, WA.
    Pretty interesting thread on Merc Canbus, HERE. It has pinouts and function, but they didn't get it done. They were trying to read the Canbus with NMEA 2000 and it didn't work without a gateway. I wonder if wiring to an OBDII could pull some info.
  11. Capt Ralph, Nov 13, 2024 at 6:46 PM
    #11
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,436
    Location:
    Satsuma, FL
    Yep, that 10 year old thread does hit that dead end. J buss I/O to N2K requires the propitiatory gateway and the propitiatory software to GUI it.

    I have a NSS12 ready for SmartCrap. Just no gateway or dash to install it.
  12. Capt J, Nov 14, 2024 at 9:58 PM
    #12
    Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,530
    Location:
    Fort Lauderdale

    Yeah, you can get vesselview mobile I think it's called, and display everything on your MFD or even your phone or tablet.