427's engine trouble

Hi,

If it was a big fumer before it may have blocked the breather.

Check the crankcase vent line is clear and un restricted.

What was done during the re build?

427 Gurus

ONe of the best places for free (and yet valuable) advice on 427s is here:
Chris Craft Commander Forum
They pretty much know it all.
Cheers!
-Eric
(didyouko nowthatthe427blockisthesameasthe390truckengineblock?)

Valve covers

I used to race these in the sixties on drag strips. Once had this occur after installing aftermarket valve covers. If you did not reinstall the originals, the stuff available physically fits but they do not have the factory baffles below the breathers to deflect oil splash. Sometimes there is a left and right cover. Another item to check is the hose coming from the valve cover to to the carb base. If you did not have it replaced at overhaul there is a good chance it is either retricted or blocked all together. One more item is the design of aftermarket breather caps. Factory ones are larges and have a very dense screen to coalesce oil vapors and it will then drain back into the engine. If you have smoke coming out with the oil then it is blow-by related. If not then what I listed above should put you back on track.

Valve cover revisited.

If the carb base plate was changed or the incorrect gasket beneath it or the carb will block off the vacuum port into the intake manifold. Easily checked by removing the breather hose running to the carb base at the valve cover while running to see if there is vacuum available. If not you've found your problem.

Ford 427s have an exhaust crossover that runs through the intake manifold from the front exhaust port on one bank to the rearmost exhaust port on the other bank. The crossover rots out at a thin spot on the underside, which puts exhaust directly into the crankcase. You don't notice it so much at low RPM, but as you open the throttles the volume of exhaust pressurizing the crankcase overwhelms the PCV system and starts blowing oil mist and exhaust out the breather (and everywhere else it can find a way out).

The fix for this requires pulling the intake manifold. There is no other way. You either replace the manifold with a new aluminum one (they're available online, just be sure to get the "non-EGR" version that doesn't have a crossover.

Alternatively, get some thin stainless steel stock and trim it so it just fills the crossover port hole in the intake manifold gasket, thereby blocking off the crossover port. I've heard that SS butter knives are the perfect thickness.

Oh, and change your oil. You've got a lot of byproducts of combustion going through the engine.

427 parts

You could not be in a better area for 427 marine parts.


Marine sales & Repair Inc.
Marine Sales & Repair, New & used engines & equipment - ask for Earl.
30134 S. River rd.
Harrison township, MI


Total Performance
Mt. Clemmons, MI
Groesbeck, ave. -ask for John Versmeerch, tell em' Jim sent ya!


Both these outfits have what you need and more, they are like a candy store for
Vintage motors, earl's place is unbelievable for anything you need on a Chris.

hey!
How are you, are you working on your boat yourself, I have not started yet, but in the spring we will replace four square meters of the hull plates

Hello oneiros!

Finding a shop that could get my motors done right and done by late May has been an ordeal, But we are getting it done,
For now, I am concentrating on items in the engine compartment that I can access now with the engines removed, ie, air conditioning, bilge pump, maybe some soundproofing.

I really wanted to replace steering system with a Seastar unit but money is very tight with the rebuilds.

The present system is not so bad as long as I remember to keep the turnbuckles tightened
On the upper helm cables.

Hope all is well.

Ok I have restored my engine 2007 has passed 130 hours the Detroit Diesel 8.5 l we here in Sweden find that gasoline engines are not as good .petrol is expensive and explosive, I have isolated the engine compartment with sheet metal that has micro small holes absorb sound, it works perfectly
Erik the swed

Ok I have restored my engine 2007 has passed 130 hours the Detroit Diesel 8.5 l we here in Sweden find that gasoline engines are not as good. Petrol is expensive and explosive, I have isolated the engine compartment with sheet metal that has micro small holes absorb sound, it works perfectly

Yes Eric, I too would like diesels. But there is a dirty little word called "tuition" that prevents me from going down that very coveted road.

That sounds like a very productive winter lay-up!
I did the Bennett conversion, probably the most bang for the buck of anything I've done to date.
They give added speed with less drag, but the real pay-off comes when running with a heavy fuel load. I have to believe they have paid for themselves in one season.