Man CR800 6 cyl sensors

What sensors is he looking for specifically? Having a schematic isn't going to help much as it won't show you where each sensor is located generally, just that it exists.

That's a square black cap that has the sender underneath behind the air filter. Usually about 4-6" from the air filter. The black cap with the wiring usually has a small phillips screw in the center holding it onto the sender. These senders can go bad if someone cleaned the air filter on the washable air filters and got overzealous with the air filter oil. Right now I'm managing 2 yachts with common rails. 1100's and the brand new 800's and I don't believe this is the same motor as your buddies as it's a brand new design, 2019 engine.

Those new i6 800's look to be a great engine. Updated cooling system from the r6. Interested in hearing your thoughts over time on this model.

The set I'm managing has around 135 hours already and most of them at cruise. But I think I've added 2 quarts of oil to each engine in the 135 hours. We had a very minor raw water leak on both motors on the hard pipe aft joint on the hard pipe leaving the heat exchanger, both fixed under warranty. They run smooth, are quiet and powerful, no vibration. The only downside is if you have to pour oil into the engine you have to remove a plastic cover that goes over the entire top of the engine and that would take time and be a pain in the rear. Not really a fan of the big decorative covers on the top and sides of the engine. They look nice, but I'd rather see the engine itself easily for leaks and things of that nature. I've also run the new 1400's and those were a beast in the torque department.

Good to hear. The MAN dealer I use said they remove the plastic decorative cover and leave it off. If I were to buy new today that would be my top engine choice.

Ha. A 42 Mag Bay FB with twin 800hp MAN's should perform just fine with room on center line of ER forward to mount a Seakeeper 6.

I go much bigger it is tough to salmon fish and the fuel burn at some point becomes a factor with how long our runs are to the Ocean.

I would assume once broken in they will require no oil in between changes.

Most of the yacht mananufacturers are now putting them closer to the stern, versus front of the engine room. They seem to have more of an effect closer to the stern I believe.

80% of our running with the 800 MAN's was at 80% load as we blazed all over the Bahamas. I did a lot of miles on each trip and added 1 quart per motor...….give or take...…..Our last trip we did 10 days (Fort Laud-Nassau-Cave Cay (exumas)- Staniel- Highbourne- Nassau), left the boat there for 5 days and did Nassau-Spanish Wells-Harbor Island-Highbourne-Shroud-Nassau-Ft. Laud each motor used 1 qt over the entire trip. They were 2/3 way up between add and full. Our previous trip was similar and all over the Abacos. But sadly, my tenure will end with them very shortly as the owner is trading it in on a new 66' MY with 1200 MAN's...….that will be here in 2 months.

Not to derail this thread too much but my concern with placing the Seakeeper in the lazarette is access to all the important items in that space. The Sporfish style boats I have seen would make changing a pump or cycling a thru hull in that area challenging. Maybe with the larger hatch you could lay on top of the Seakeeper and reach most items. It looks like though you would have to pull fish boxes to really get at anything and assuming you seal them well they can be a pain to get out on any frequency. I have already had both mine out and wouldn't want to do it every time I wanted to inspect or service items in the lazarette area. Everything on a boat is a compromise. I think a 40 to 42ft boat is a great size to feel the advantages of a Seakeeper if you can find a mounting location that doesn't make getting to other important mechanical items an obstacle. I would add one to my boat today if I had a suitable mounting location.

I don't see manufacturers putting the seakeeper in the lazarette generally. I see most manufacturers them putting them at the aft of the engine room versus in front of the motors. Hatteras does put the seakeepers right in the stern lazarette on the 60' motor yacht, but the only one I can think of at the moment. Princess puts them in the generator room under the aft deck but forward of the stern crew quarters on their 62' motor yacht. Etc. fast SF tend to like the trim a little aft of the LCB, given the speed they cruise at, then a little trim tab brings the bow down to where you want it and creates stern lift at the same time.

Viking has been using the Lazarette location aft for most Seakeeper installs.

I agree with Pac Blue. Unfortunately that is also why that space aft in Engine room is a great spot for the generator. Perhaps Mag Bay will chime in and let us know what location they came up with on the 42 for the Seakeeper.