Click for Cross Click for YF Listing Service Click for Burger Click for Abeking Click for Northern Lights

Bosch Govenor Failure 12 valve mtu 183 te 92

Discussion in 'Technical Discussion' started by Geobsum, Sep 26, 2015.

You need to be registered and signed in to view this content.
Page 2 of 2
  1. Marmot, Sep 28, 2015
    #21
    Marmot

    Marmot Senior Member

    Joined:
    May 20, 2007
    Messages:
    3,311
    Location:
    9114 S. Central Ave
    If it were my boat I would research those alternatives very closely and have a heart to heart with my insurance broker (or my lawyer) about the type of casualties that are covered. There might even be a clause that covers losses created by "operator error."

    If I were to try deep frying a turkey in the galley and forgot I left the burner on and the stove was destroyed when flaming oil spilled all over it, wouldn't it be replaced by insurance? So, what is the difference when it has been established that the engine failed after the operator placed the gear in neutral?
  2. Capt J, Oct 1, 2015
    #22
    Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,531
    Location:
    Fort Lauderdale
    If you can prove that the emergency shutdowns were maintained and they failed to shutdown the engine, then possibly you can get the insurance to pay via that route. I don't think there are any inherent issues (defects) and have not heard of any on the Bosch side of things on 12v183's.
  3. Geobsum, Nov 3, 2015
    #23
    Geobsum

    Geobsum Member

    Joined:
    Jul 28, 2014
    Messages:
    47
    Location:
    Ohio
    For everyone who responded here is the photo taken at rpm showing that the full load stop in the intermediate governor housing broke and was loose and moving around in the housing and probably caused the jam and over speed. No other problem was found.

    Attached Files:

  4. Geobsum, Nov 3, 2015
    #24
    Geobsum

    Geobsum Member

    Joined:
    Jul 28, 2014
    Messages:
    47
    Location:
    Ohio
    Sorry wrong photo

    Attached Files:

  5. Marmot, Nov 6, 2015
    #25
    Marmot

    Marmot Senior Member

    Joined:
    May 20, 2007
    Messages:
    3,311
    Location:
    9114 S. Central Ave
    Interesting. Have you talked to your insurer about this? It seems like the casualty was not a "normal wear and tear" issue but a catastrophic event due to (rare?) material failure. Ask the shop to document the manufacturer's recommended replacement time for the part that broke (that should be fun) and ask them how many similar failures have occurred. This may be well worth pursuing an insurance claim.
  6. Geobsum, Nov 11, 2015
    #26
    Geobsum

    Geobsum Member

    Joined:
    Jul 28, 2014
    Messages:
    47
    Location:
    Ohio
  7. Geobsum, Nov 11, 2015
    #27
    Geobsum

    Geobsum Member

    Joined:
    Jul 28, 2014
    Messages:
    47
    Location:
    Ohio
    RPM issued a report noting the failure and stating may have possibly been due to fatigue because of age of engine and hours of service, and confirmed no other cause found. I argued and proved low hours (1045) thru three surveys over the years. Also got them to admit that the broken arm is not a serviceable part and they have never seen this failure before, Ever! My insurance company is evaluating.
  8. olderboater, Nov 11, 2015
    #28
    olderboater

    olderboater Senior Member

    Joined:
    Sep 2, 2013
    Messages:
    7,130
    Location:
    Fort Lauderdale
    Have you looked at and read your policy closely? Insurance policies as well as how the companies respond varies widely. Sometimes it's just a very few words that make the difference. Some policies while they would not cover the part failure would cover the damage caused as a result of it. Other policies would not. There are generally clauses in the policy excluding or including. Out policy does cover latent defects. Many don't.
  9. Geobsum, Nov 24, 2015
    #29
    Geobsum

    Geobsum Member

    Joined:
    Jul 28, 2014
    Messages:
    47
    Location:
    Ohio
    I'm happy to report that my insurance company has assured me of coverage and has authorized me to order a new long block from RPM. It has been a two month battle which was won in part my the help and advice from this forum!
    The last fight was they wanted to depreciate the long block down to 30% and then apply a $9800 deductible. I had to go over the adjuster's head to higher management where I convinced them that the quote that I got was for a used engine not a new one and no depreciation should apply. Management agreed and has waived depreciation but I will still have the deductible.
    Thank you all again.
  10. K1W1, Nov 25, 2015
    #30
    K1W1

    K1W1 Senior Member

    Joined:
    Sep 30, 2005
    Messages:
    7,427
    Location:
    My Office
    That is good news. Are they also going to stump up for the removal and refit of the engine?
  11. Geobsum, Nov 25, 2015
    #31
    Geobsum

    Geobsum Member

    Joined:
    Jul 28, 2014
    Messages:
    47
    Location:
    Ohio
    Yes, so they have assured me in writing subject to review as the work proceeds.
  12. Capt J, Nov 25, 2015
    #32
    Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,531
    Location:
    Fort Lauderdale
    Glad to hear it's working out for you. It might be wise to inspect the other engine and replace that part as well, before it breaks.
  13. K1W1, Nov 25, 2015
    #33
    K1W1

    K1W1 Senior Member

    Joined:
    Sep 30, 2005
    Messages:
    7,427
    Location:
    My Office
    That is excellent advice
Page 2 of 2