Click for Mulder Click for Westport Click for Abeking Click for YF Listing Service Click for JetForums

FR8252 25kw radar antenna not turning

Discussion in 'Technical Discussion' started by CSkipR, Feb 12, 2013.

You need to be registered and signed in to view this content.
  1. CSkipR, Feb 12, 2013
    #1
    CSkipR

    CSkipR Member

    Joined:
    Aug 16, 2008
    Messages:
    965
    Location:
    New Smyrna Beach, Fl
    The 6 ft antenna is no longer turning. Checked fuses and they are good. Manual says replace antenna drive mechanism. Anyone done this before or have any input would be appreciated. Where did you purchase part, etc.
  2. NYCAP123, Feb 12, 2013
    #2
    NYCAP123

    NYCAP123 Senior Member

    Joined:
    Mar 14, 2008
    Messages:
    11,208
    Location:
    Long Island, NY
    We had the scanner repaired by Raymarine last summer and were extremely disappointed in their service. We were told they have a 20 day backlog before even looking at a unit. We were without radar almost the entire summer.
  3. K1W1, Feb 12, 2013
    #3
    K1W1

    K1W1 Senior Member

    Joined:
    Sep 30, 2005
    Messages:
    7,427
    Location:
    My Office
    Hi,

    Check that you have power to the unit, that any connections are tight and clean.

    If all else fails and you are reasonable competent.

    If you can get the cover off check as far as you can the brushes inthe miter are free and in contact wuth the commutator.

    Failing that take it off, strip it down and order the parts you need from a Furuno dealer.


    Start simple, make sure there is power going to the scanner, just because it is turned on at the BDU doesn't mean that the message is getting through to the scanner.
  4. CSkipR, Feb 12, 2013
    #4
    CSkipR

    CSkipR Member

    Joined:
    Aug 16, 2008
    Messages:
    965
    Location:
    New Smyrna Beach, Fl
    I have checked power to the screen and that is fine. Haven't checked power to antenna yet.
  5. Capt Ralph, Feb 12, 2013
    #5
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,439
    Location:
    Satsuma, FL
    Skip
    I have worked on some of the old Furuno stuff. Bad connects were usually the big culprits. You have to crack the pedestal and find the dc leads and measure good VB+ upstairs. I do not remember any fuses in the pedestal. Just a lot of room for bad connections. Depending on your displays model, a few cheap fuse holders were on the back, On some models (big, old, heavy) there were some pico fuses on the different boards inside (the display).
    A question, do you get a bright radius line on the display when you try to operate? It would be in the direction the array is pointing. This tells us if the pedestal is alive at all. Any error messages? even the old units would give a timing/heading error if the pedestal was alive at all. if it just sits there and no messages after 2 minutes, there is no VB+ to the pedestal.
    Keep in touch,
    rc
  6. CSkipR, Feb 13, 2013
    #6
    CSkipR

    CSkipR Member

    Joined:
    Aug 16, 2008
    Messages:
    965
    Location:
    New Smyrna Beach, Fl
    I get a faint very weak small circle on the display screen and the array does not turn. Actually now the small weak circle has disappeared and theres nothing on the screen. I believe the array (pedestal) is alive although barely breathing. I've checked all fuses and they are good.
  7. CSkipR, Feb 13, 2013
    #7
    CSkipR

    CSkipR Member

    Joined:
    Aug 16, 2008
    Messages:
    965
    Location:
    New Smyrna Beach, Fl
    Fr8252

    Okay unbolted the top of the array and checked for loose connections inside. Although didn't find anything that I noticed to be loose when we shut the top of the radar it started working again. So problem resolved for awhile.
  8. Capt Ralph, Feb 13, 2013
    #8
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,439
    Location:
    Satsuma, FL
    Yep, it's on a boat. Keep a mallet around. When it fails again, just go up there and rap it a few times.
    When you get tired of fixing your stuff this way, go after that bad connect or wire.
    BTW, I like beating on things to make them work. That's why I still run Ole Detroit's.

    71's rule,
    rc