Click for Ocean Alexander Click for JetForums Click for Westport Click for Glendinning Click for Mulder

Replacing Engine pencil zincs

Discussion in 'Technical Discussion' started by Dave Stranks, Dec 2, 2012.

You need to be registered and signed in to view this content.
  1. Dave Stranks, Dec 2, 2012
    #1
    Dave Stranks

    Dave Stranks Member

    Joined:
    Sep 6, 2008
    Messages:
    67
    Location:
    Coal Harbor Vancouver
    Its time to replace the engine zincs and this year i just bought the zinc part not with the brass caps
    How do you get the zinc piece that breaks off in the inter thread of the brass cap' Tried a small drill and then ramming a flathead screw driver and twisting Like a pain is there a easier way
  2. K1W1, Dec 2, 2012
    #2
    K1W1

    K1W1 Senior Member

    Joined:
    Sep 30, 2005
    Messages:
    7,427
    Location:
    My Office
    Hi,

    Drill a hole and use a fluted easy out.

    Easier still change them before they get that worn and you still have something to grip.
  3. Marmot, Dec 3, 2012
    #3
    Marmot

    Marmot Senior Member

    Joined:
    May 20, 2007
    Messages:
    3,311
    Location:
    9114 S. Central Ave
    Soak them in muriatic acid for a few hours.
  4. dsharp, Dec 4, 2012
    #4
    dsharp

    dsharp Senior Member

    Joined:
    Aug 23, 2009
    Messages:
    240
    Location:
    lake jackson, tx
    That's the way I've always done it. Be sure and don't breath the fumes.
  5. Capt Ralph, Dec 5, 2012
    #5
    Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    13,439
    Location:
    Satsuma, FL
    I can't wait to try that. What a great idea.
  6. dennismc, Dec 5, 2012
    #6
    dennismc

    dennismc Senior Member

    Joined:
    Jan 29, 2009
    Messages:
    1,177
    Location:
    Vancouver BC
    Depending on you engine and cooling system set up, you may find that the salt water cooling actually drains down below the level of the zincs on engine shut down and the zincs are only getting worn by the velocity of the cooling water flow, in which case they actually are redundant, worth checking, mine have been eliminated for 15 yrs now and I drain the residual from the hex after every shutdown, so far all is well.
  7. Dave Stranks, Dec 30, 2012
    #7
    Dave Stranks

    Dave Stranks Member

    Joined:
    Sep 6, 2008
    Messages:
    67
    Location:
    Coal Harbor Vancouver
    The zincs were not eaten away as bad as the first time i changed out but still it was impossible to unthread without breaking it off at the flush
    Tried sulmamic acid for a couple of hours did really cut it
    Looked up on the net that brass melting point was around 800 and zinc 400 so i used a propane torch to heat it up and knocked it on the stainless engine room countertop (cold so instant cooling) came right out noooo problem
    New one went in real easy
    Learned something to day
  8. Opcn, Mar 19, 2013
    #8
    Opcn

    Opcn Senior Member

    Joined:
    Mar 15, 2009
    Messages:
    478
    Location:
    Nordland (near Port Townsend), WA, USA
    Be careful knocking around hot metal components. They get soft at a much cooler temperature than they melt.