A/C Compressor question

If you have scroll compressors, than they should be hot to the touch on top with a proper gas charge and every thing else working right. The one that is not hot is the one that I would look into more and I would start by throwing some gauges on the unit to see the psi.

Have you seen the price increase of 22 lately? Last I heard $400 for a 30lb jug that normally went for $130. They are trying to eradicate R22.
Be aware that if you over charge than your not going to be transferring heat properly and really be doing yourself a disfavor.

I agree don't overcharge. I've heard that when the patent runs out for Dupont on like R 12, and then R 22, the EPA seems to find that it is not environmentally friendly and phases it out and all of a sudden Dupont has a new freon, such as the R143 that replaced R12 and the R410 that is replacing R22 with well a new patent.......

Hi,

Some more half baked idiotic advice there is it?

Yourself anyone who is thinking of recharging a R22 System with R410 should read this first.

What You Should Know about Refrigerants When Purchasing or Repairing a Residential A/C System or Heat Pump | Ozone Layer Protection - Regulatory Programs | US EPA

These questions can't be answered without more information.
Post a picture of each compressor.(are they the same model)find and post model number & manufacturer. What gas are they charged with? Then measure the temperature on top of the compressor or line comming out(discharge temp.). Most hermetic compressors reject ~5% to ~15% of their heat through the shell.

There are different types of compressors ,some can get hot from being overcharged. Someone may have replaced the capacitor with the wrong microfarad (uF) one causing it to run hot.....

Running hot may be normal, or not,just not enough information to diagnose properly

Hi,

If both are fed by the same pump you should check the SW side of things.

See if the water is flowing into the condenser ok, see if it flows out at a similar rate and then see if it flows overboard at a similar rate.

If there is good flow at the inlet and not much at the outlet a coil cleaning maybe the answer.

One of the first things I do when I want to get an idea of a system charge or operational issues is to feel the condensing coils (the coil that the sea water runs through to cool the hot gas). They should be toasty warm (110,118F or so all depending) and they should be comfortable to hold your hand on. If they are to hot to hold then there can be a sea water flow issue. I find muscles all the time blocking tubes up. If they are cold (like 80,90F or so) then you will more than likely be low on gas.
Of course there are always variables but 9 out of 10 and just a rough guide...

I am pretty sure Capt J was referring to the fact that R22 systems are replaced by R410 systems which is correct. EPA in America has shut down manufacturing of R22 units. Most of us are not thrilled by this decision. You can no longer buy R22 internal system parts (legitimately) and you have to replace the whole unit on a small failure.

UMMMM NO, do not put R410 in a unit meant to use R22, it is not a drop in replacement, neither is R143 for R12 (but R12>R143 can be done by changing the dryer, evacuating all of the oil from the system, and a few other small changes). What I was saying, is R410 was designed to replace R22 in units that used to be manufactured to use R22, now have to be made to use R410. R410 runs at much higher pressures both High and Low side. Unit's such as refrigerators, household air conditioners, etc etc etc now have to be manufactured for use with R410........I was trying to say that R410 was designed to replace the now not-manufactured R22, when new units are manufactured they are required to be R 410.

Typical nonsense. An R22 system can be serviced as long as the owner is willing to pay for it. R22 can still be imported and R22 is available.

The EPA does not require an R22 unit to be replaced or prohibit it from being repaired or refilled with R22 after repairs.

A knowledgeable chief engineer will know the regulations so that the owner is not faced with large expenditures due to the engineer's ignorance.

The regulations governing what can be done to an existing unit and who can perform the work are easily found. The EPA website is a good place to start. It takes less time to obtain the actual rules and regs than it does to post nonsense that might mislead others.

A wiser member than me on YF told me that if I lay down with the dogs I will get flees. You guys just enjoy being rude and I am going to play fetch with you any more.

Does that mean you are "fleeing" the scene?

There is a better idiom than the thing about dogs, it is the one that says it is "better to remain silent ... "